#Where to purcahse lvl beams span tables how to#

LVL is also straighter and of more uniform dimensions than regular lumber, and is less likely to shrink, twist, warp, or bow. Since the layers of wood grain all run parallel to each other, LVL is similar to solid wood, but at least twice as strong. The stacks then pass into a machine that produces high heat and pressure to ensure a strong, long-lasting adhesive bond between layers. The number of sheets in the stack determines the thickness of the laminated beam. The glued sheets are then stacked with the grain running longitudinally like solid lumber not alternating longitudinally and latitudinally as with plywood. The veneer then passes through a gluing machine that applies a thin layer of waterproof adhesive. Once dried and trimmed, the sheets pass through a sander or grinder that flattens and smooths them to a consistent thickness. The veneer sheet is then dried with hot air, causing it to shrink some, and then it is trimmed to size for LVL production. The logs are debarked, pressure steamed with a mix of water vapor and chemicals for 48-hours, and then run through a veneer peeler that ‘unrolls’ the log into a continuous sheet with a thickness between 1/16” and 1/4”.

It is made in a similar manner to plywood using softwood veneer logs or peelers. LVL or laminated veneer lumber was used to make propellers for aircraft in WW2 but didn’t become a construction material until the mid-1970s.

How Far Can an LVL Beam Span Without Support?.

Our goal is to provide you with information to help with your next or current building project.

#Where to purcahse lvl beams span tables how to#

Additionally, we look at how to install an LVL beam. We explain how to determine beam size and also discuss their cost. In this article, we’ll identify what LVL beams are, their different sizes, how far they can span, and their different uses. Depending on its width, depth, and load parameters, an LVL beam can span up to 80-feet. The layers are heated, glued, and pressed together in different widths or thicknesses, and then cut to depths to meet various load requirements. After explaining what it was and the LVL beam span, I decided to give it a try, but I also wanted more information.Īn LVL or laminated veneer lumber beam is made up of thin layers of wood veneer similar to plywood. Such was a recent experience when I was looking for a beam for a renovation project. I didn't realize that the lumber yard could provide expert consultation in this way, so that suggestion was very helpful.Every time I wander through my local lumber store, I seem to encounter a new product, not that it’s all that new, just to my awareness or my location. I'd love to lower the foundation, but at what expense? Going lower on the foundation would have meant double the drilling since now I'm exposing more ledge area and it's more solid. That got me an extra foot in the basement, to a 7' ceiling if I used 2x8's for joists. I spent a week drilling holes (130) in the ledge and pouring in Dexpan to break it up to the point where a small hammer on a skid steer could bust it out. Blasting is not an option due to cost, and I doubt that any demolition person would do that when it's right next to another structure. When we dug the hole, we hit ledge at 6 feet down. I may keep the 8' LVLs and use them to stiffen the floor in the older section.Īs for 'refusing' to drop the foundation, or raising the floor: It would be better to say I'm having to make choices. This will still be much better than the house I'm adding on to where the floors are carried by 2x8's sitting on horizontal 4x4's resting on piers every 6 to 10 feet. He said that if I used a triple 12', then the floor would be perfectly stiff, but the double would be fine.

Said that if I put in a center post, I could stay with the 8', but I don't want that. I dropped in on them this morning and after looking it over and doing some calculations, they said I needed to swap out my 8' LVLs for 12'. I'm getting my materials from Hancock Lumber in Conway, NH.